Nordson VersaBlue 100H/100H Скачать руководство пользователя страница 34

Страница: 34 / 108

Installation

3-2

P/N 7146386A

2008 Nordson Corporation

VBN w/o Control System

Removing Melter

Run the melter until empty, separate all connections from the melter, and

allow the melter to cool down.

Disposing of Melter

When your Nordson product has exhausted its purpose, dispose of it

properly according to local regulations.

Installation Requirements

Set up only in an environment that corresponds to the stated Degree of

Protection (Refer to section

Technical Data

). Do not set up in a potentially

explosive atmosphere! Protect from vibration.

CAUTION:

Protect the control panel from direct sunlight. The UV rays

reduce the service life of the liquid crystals.

Exhausting Material Vapors

Ensure that material vapors do not exceed the prescribed limits. Always

observe the safety data sheet (MSDS) for the material to be processed. If

necessary, exhaust material vapors and provide sufficient ventilation of the

location of the system.

Fig. 3-2

Содержание VersaBlue 100H/100H













































































































Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды

Nordson VersaBlue 100H/100H, Руководство пользователя

Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды