Nordson VersaBlue 100H/100H Скачать руководство пользователя

Страница: 82 / 108

Tank side

Pump side

Repair

7-2

P/N 7146386A

2008 Nordson Corporation

VBN w/o Control System

Replacing Gear Pump

Nordson recommends replacing the pump and sending the old one in to be

repaired.

WARNING:

Hot! Risk of burns. Wear appropriate protective

clothing/equipment.

Tank Isolation Valve

NOTE:

Operate the tank isolation valve only when the melter is heated to

operating temperature.
Pin in position

: Closed

Pin in position

: Open

Fig. 7-1

Detaching Gear Pump

1. Close tank isolation valve.

NOTE:

Detach the gear pump only when the material is soft (70

C/158

depending on material).

CAUTION:

The motor is precisely aligned and may not be be slid back with

the bracket in the slot.

2. Turn the coupling until the screws of the coupling half shells are more

easily accessible.

3. Release the screws of the coupling half shells on the pump side.
4. The released coupling halves can fall apart. Remove carefully to prevent

separation. Store the coupling halves and protect them from dust. They

will be needed again.

5. Place a container under the pump (1) to collect any material left.
6. Detach pump.
7. Clean sealing surface on the plate (2). If necessary, heat material

residue with a hot air fan, then remove.

8. Allow melter to cool to room temperature.

Fig. 7-2

Содержание VersaBlue 100H/100H













































































































Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды

Nordson VersaBlue 100H/100H, Руководство пользователя

Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды