Nordson VersaBlue 100H/100H Скачать руководство пользователя страница 63

Страница: 63 / 108

Maintenance

5-13

P/N 7146386A

2008 Nordson Corporation

VBN w/o Control System

Filter Cartridge

Replacing Filter Cartridge

WARNING:

Hot! Risk of burns. Wear appropriate protective

clothing/equipment.

WARNING:

System and material pressurized. Relieve system pressure.

Failure to observe can result in serious burns.

Removing Filter Cartridge

Nordson recommends keeping a supply of filter cartridges on hand to

prevent disruptions in production.

NOTE:

Remove the filter cartridge when the melter is hot and not under

pressure.

M10

Size 24

Fig. 5-12

CAUTION:

Stop turning as soon as the thread is free; otherwise part of the

filter cartridge could remain in the bore.

Use e.g. a pliers to extract the filter cartridge.

If the Tank is not Empty

WARNING:

Hot! Risk of burns. Wear heat-protective gloves.

1. Allow the unit to cool until the adhesive is somewhat viscous.
2. Use e.g. a pliers to extract the filter cartridge.
3. Collect any adhesive that may escape (bowl).
4. Quickly screw in a replacement filter cartridge or a plug, then clean the

filter cartridge.

Содержание VersaBlue 100H/100H













































































































Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды

Nordson VersaBlue 100H/100H, Руководство пользователя

Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды