Nordson HORIZON 200 Скачать руководство пользователя страница 47

Страница: 47 / 124

Maintenance

5-1

Part 106913

−

2018 Nordson Corporation

Section 5

Maintenance

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

Daily Maintenance

Perform these procedures daily to keep your system clean and functioning

properly.

Cleaning

Perform this procedure daily and when changing powder color or type.

WARNING:

Wear an approved respirator and safety glasses or goggles

when performing maintenance or cleaning operations. Obtain and read

Material Safety Data Sheets for each powder used.

1. Turn off the automatic-gun master-control unit(s) and manual-gun

control units.

2. Turn on the exhaust fan.
3. Disconnect the powder-feed hoses from the powder pumps. Blow the

powder out of the hoses and spray guns with compressed air.

4. Ground the gun electrodes and clean the spray guns according to the

instructions in the spray gun manuals.

5. Clean the enclosure roof, walls, and floor with a rubber squeegee. Push

the collected powder into the color module.

6. Remove the remaining powder residue from the enclosure with an

air-powered vacuum and a soft brush attachment. Wipe down all

surfaces with a damp, lint-free cloth (do not use tack cloths). If you

remove the color module, clean the floor inlet and surrounding area.

7. Turn off the exhaust fan.
8. Clean the operator’s platform and the floor around the booth.

Содержание HORIZON 200





























































































































Результаты поиска

Содержание HORIZON 200

Отзывы:

Похожие инструкции для HORIZON 200

Бренды по названию

Популярные бренды

Nordson HORIZON 200, Руководство по эксплуатации продукта

Результаты поиска

Содержание HORIZON 200

Отзывы:

Похожие инструкции для HORIZON 200

Бренды по названию

Популярные бренды