Nordson HORIZON 200 Скачать руководство пользователя страница 34

Страница: 34 / 124

Operation

3-8

Part 106913

−

2018 Nordson Corporation

Vent-Assist Air Pressure Adjustment

To maintain a neutral air pressure in the sieve so it can function properly, the

compressed air used to convey the reclaimed powder to the accumulator is

vented into the color module. Vent-assist air creates low pressure in the

vent tube and increases the air flow. Use the following procedure to adjust

the vent-assist air pressure.

NOTE:

The vent-assist air pressure regulator is located either on the sieve

pneumatic panel, or on the system pneumatic panel.
1. Disconnect the scrap hose from the sieve.
2. Secure a paper or plastic bag to the scrap port with a worm clamp, cable

tie, or rubber band.

3. Start the exhaust fan, sieve, and transfer pumps.
4. Watch the bag. If it inflates, increase the vent-assist air pressure. If it

deflates, decrease the vent-assist air pressure.

Daily Startup and Shutdown Procedures

Use these procedures for routine operation of your system.

Startup

1. Turn on the system electrical power and compressed air supply.
2. Walk around the booth and verify that the:

system equipment is connected to ground

flame detector system is on

skirt seal is securely fastened to the color module and base

transfer and feed hoses are connected to the pumps, accumulators,

and spray guns.

3. Turn on the exhaust fan. Set the transfer pump switch to AUTO. Set

the conveyor switch to NORM.

4. Turn on the automatic-gun master control unit and the manual-gun

control units.

5. Adjust the kV settings and the powder-pump air pressures, if necessary.

Refer to your spray gun and control unit manuals.

6. Start the conveyor and start spraying workpieces.
7. Check the air flow through the enclosure. Make sure the sprayed

powder is not being pulled from the spray guns and workpieces, or

escaping from the enclosure openings. Adjust the fan damper (Horizon

400 only) as needed. Air flow through each opening must be

maintained at 30 m/min (100 fpm), minimum.

Содержание HORIZON 200





























































































































Результаты поиска

Содержание HORIZON 200

Отзывы:

Похожие инструкции для HORIZON 200

Бренды по названию

Популярные бренды

Nordson HORIZON 200, Руководство по эксплуатации продукта

Результаты поиска

Содержание HORIZON 200

Отзывы:

Похожие инструкции для HORIZON 200

Бренды по названию

Популярные бренды