Nabtesco RV RS Series Скачать руководство пользователя

Страница: 11 / 42

Chapter 2 Product Overview

Product Overview

Chapter 2

This chapter describes an overview of this product.

Name of each section

2.1.

This section provides an explanation of the name of each section.

If the shape of the actual section differs from the illustration below, refer to the separately provided “Outer
dimensions” drawings and specification sheet.

(1) RS-260A

(2) RS-320A

Fig. 2-1

Hole for installing
reduction gear

Tapped hole for installing component

(Tapped hole for hanging bolt)

Installation
reference
surface

(3 locations)

Tapped hole for
injecting/draining
grease

(Component
to be rotated)

Center pipe

(Wiring and hollow hole for wiring)

(Component to be fixed)

Base flange

Tapped hole for installing motor flange

Output flange

Tapped hole
for injecting/draining grease

Fig. 2-2

Tapped hole for hanging bolt

Hole for installing
reduction gear

Tapped hole for installing component

Base flange

Tapped hole for installing motor flange

Output flange

(Component to be fixed)

Installation
reference surface
(3 locations)

Tapped hole for

injecting/draining grease

(Component to be rotated)

Center pipe

(Wiring and hollow hole
for wiring)

Tapped hole for

injecting/draining grease

Содержание RV RS Series











































Результаты поиска

Содержание RV RS Series

Отзывы:

Похожие инструкции для RV RS Series

Бренды по названию

Популярные бренды

Nabtesco RV RS Series, Руководство по эксплуатации

Результаты поиска

Содержание RV RS Series

Отзывы:

Похожие инструкции для RV RS Series

Бренды по названию

Популярные бренды