Nabtesco RV RS Series Скачать руководство пользователя | Manualshive

Страница: 22 / 42

background image

Chapter 5 Installation

14

Installation

Chapter 5

This chapter describes the installation of this product.

Before installation, take care regarding the following precautions.

• Do not stand on top of the reduction gear or put anything on it.

• Be sure to install the reduction gear with the correct orientation.



Standing on top of the reduction gear or putting something on it could cause damage to the
reduction gear.



Installing the reduction gear with an incorrect orientation could cause damage to the customer’s
device and the reduction gear.



The center pipe at the center of the reduction unit is not designed to support a load. Do not use the
reduction gear in any way that applies a load to the center pipe. The oil seals may become
deformed, which could eventually cause leakage of the lubricant.

Installation position

5.1.

• When installing the reduction gear in the horizontal shaft position, do not position the input shaft

(motor) upward. (Install the reduction gear with the input shaft facing left, right, or down.)

• For the RS-260A, do not attach the reduction gear to the ceiling.



If the input shaft side is oriented upward, lubrication of some parts may be adversely affected. This
could cause damage to the reduction gear.

Note

Fig. 5-1

Example of correct installation

Example of incorrect installation

Top

Motor

Bottom

Reduction gear

Bottom

Reduction gear

Motor

Top

«
...
20
21
22
23
24
...
»

Содержание RV RS Series











































Отзывы:

Нет отзывов

Похожие инструкции для RV RS Series

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: ACS Страницы: 56

Movie FL Black E27 Flaps

Бренд: Qazqa Страницы: 2

Бренд: Hammer Strength Страницы: 18

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: zarges Страницы: 36

Бренд: Ofa Bamberg Страницы: 80

Бренд: Gardco Страницы: 17

Бренд: H&S Страницы: 42

Бренд: Aeroflex Страницы: 211

Бренд: Dantel Страницы: 22

bionic power knee

Бренд: Össur Страницы: 2

BALANCE KNEE OM8

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 37

REBOUND DIABETIC WALKER

Бренд: Össur Страницы: 63

Бренд: Össur Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды