background image

Contents 

Operation .................................................................................................... 25

Chapter 6

Checking before operation ....................................................................................................................... 25

6.1.

Running-in operation ............................................................................................................................... 25

6.2.

Precautions for operation ......................................................................................................................... 25

6.3.

Servomotor ............................................................................................................................................... 26

6.4.

Maintenance and Inspection ..................................................................... 27

Chapter 7

Precautions on maintenance ..................................................................................................................... 27

7.1.

Daily inspection ....................................................................................................................................... 27

7.2.

Precautions when handling the lubricant ................................................................................................. 28

7.3.

Lubricant replacement.............................................................................................................................. 29

7.4.

Troubleshooting checksheet ..................................................................................................................... 33

7.5.

Contact Information 

Содержание RV RS Series











































Отзывы: