Nabtesco RV RS Series Скачать руководство пользователя | Manualshive

Страница: 12 / 42

background image

Chapter 2 Product Overview

4

(3) RS-900A



The shape of the reduction gear may differ from the illustration depending on the ordered
specifications.

Lubricant

2.2.

• The specified lubricant is filled before shipping.

• When replacing the lubricant, be sure to use the Nabtesco-specified lubricant. For purchase of the

lubricant, contact our service representative.

• Do not mix it with other lubricants.

Table 2-1

Model

RS-260A

RS-320A, RS-900A

Brand specified by Nabtesco

VIGOGREASE* RE0

Molywhite RE No. 00

Operating temperature range

(ambient temperature)

-10 to 40°C

-10 to 40°C

* VIGOGREASE is registered trademark of Nabtesco Corporation.



In order to take advantage of the performance of this product, use the Nabtesco-specified lubricant.
Using other types of lubricant could cause deterioration of performance and premature damage.



Mixing with other lubricants could cause deterioration of performance, generation of abnormal noise,
and premature damage.

Important

Note

Fig. 2-3

Hole for installing reduction gear

Tapped hole for installing component

Installation
reference
surface

(3 locations)

Tapped hole for
injecting/draining
grease

(Component to be
rotated)

Center pipe

(Wiring and hollow hole
for piping)

(Component to be fixed)

Tapped hole for installing motor
flange

Base flange

Output flange

(Tapped hole for
hanging bolt)

Tapped hole for
injecting/draining
grease

«
...
10
11
12
13
14
...
»

Содержание RV RS Series











































Отзывы:

Нет отзывов

Похожие инструкции для RV RS Series

Бренд: MacDon Страницы: 84

Бренд: MacDon Страницы: 89

Бренд: Patton electronics Страницы: 18

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Parker Страницы: 39

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды