MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 83

Страница: 83 / 186

VJ-1204 OPERATION MANUAL

4 Handling the printer

4-21

4.4.4.2

Settings that can be changed or confirmed while printing

NOTE

• The Print start menu is displayed only when the printer is warming up.

• When you change a setting during operation, be sure to select "Backup" to save the setting that you

changed.
If the printer returns to Normal without "Backup" being selected, the changed setting is not saved.

Setup item

Setting

Description

Print Start

—

• [Enter] key: If the heater temperature does not reach

the set value during warming-up, printing starts.

Temperature

Pre

Check the current Pre Heater temperature.

Platen

Check the current Platen Heater temperature.

After

Check the current After Heater temperature.

Pre Heater

Off / 30 °C to 50 °C

Change the Pre Heater temperature.

Platen Heater

Off / 30 °C to 50 °C

Change the Platen Heater temperature.

After Heater

Off / 30 °C to 50 °C

Change the After Heater temperature.

PF Adjust

–20 pulse to 0 to 20 pulse

Change the feed adjustment value.

Backup

—

• [Enter] key: Save the changed setting.

—

• [Cancel] key: The printer returns to Normal.

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды