MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 35

Страница: 35 / 186

VJ-1204 OPERATION MANUAL

3 Before using

3-9

Follow the procedure below to install the ink cartridge.

1. Turn the unit ON.

•

The printer starts the initializing operation.

•

After the initial operation is compete, "Insert CleaningCart." is displayed on the operation panel.

2. Take a cleaning cartridge out of the bag.

3. Install the cleaning cartridge into the ink cartridge slot.

•

Keep the mark of the cleaning cartridge facing up and insert it into the slot of the printer.

•

Insert the cleaning cartridge all the way to the end of the slot.

•

The printer starts filling cleaning fluid.

4. After the cleaning fluid is filled, take out the cleaning cartridge.

•

"Busy-Washing" is displayed on the operation panel and the printer starts cleaning the print head.

•

After head cleaning is complete, "Insert InkCartridges" is displayed on the operation panel.

No.

Name

Cleaning cartridge

Ink cartridge slots

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды