MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 24

Страница: 24 / 186

2 Product overview

VJ-1204 OPERATION MANUAL

2-6

TIP

• When an error requiring restart (fatal malfunction for the printer operation) occurs, all lamps blink with an alarm.

7.2.5 Error requiring restart

If the error persists even when the malfunction is fixed, contact your local MUTOH dealer.

Data lamp

Orange

Lamp

• Analyzing received data.
• Under printing.

Lamp

blinks

Receiving data.

Lamp

OFF

Data is not received and analyzed.

High lamp

Green

Lamp

The head height is set to High.

Lamp

OFF

The head height is set to Low.

Low lamp

Green

Lamp

The head height is set to Low.

Lamp

OFF

The head height is set to High.

Wave lamp

Green

Lamp

The Effect menu is set to Wave.

Lamp

OFF

The Effect menu is set to None.

Fine &S.Fine lamp

Green

Lamp

The Effect menu is set to Fine or Super Fine.

Lamp

OFF

• The Effect menu is set to Wave.
• When the Wave lamp is turned OFF, the Effect menu is set to

None.

Long lamp

Green

Lamp

• Cleaning Mode is set to Long.
• When the Normal lamp is also turned on, Cleaning Mode is set

to Short.

Lamp

OFF

Cleaning Mode is set to Normal.

Normal lamp

Green

Lamp

• Cleaning Mode is set to Normal.
• When the Long lamp is also turned on, Cleaning Mode is set

to Short.

Lamp

OFF

Cleaning Mode is set to Long.

LCD display section

—

Displays operation status of the printer or an error message.

No.

Name

Color Status

Description

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды