MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 154

Страница: 154 / 186

7 Troubleshooting

VJ-1204 OPERATION MANUAL

7-2

7.1

Malfunctions and failures

This section describes undisplayed malfunctions and failures of the printer, possible causes and
countermeasures.

7.1.1

Problems in installation and introduction

(1) Cannot perform ink replenishment

(2) Ink does not come out after ink replenishment

7.1.2

Cannot print at all

(1) Does not work at all after power activation

No.

Possible cause

Remedy

Reference

Is the front cover open or media
loading lever raised?

Close the front cover, or lower the media
loading lever.

3.4 Setting

media

Are the four ink cartridges fully
inserted?

Fully insert the four ink cartridges.

6.1.1 Replacing

ink cartridges

Is the waste fluid box fully inserted?

Fully insert the waste fluid box.

6.1.3 Replacing

waste fluid box

No.

Possible cause

Remedy

Reference

Is the ink cartridge cold and frozen?

Leave the cartridge at room temperature for
at least 3 hours, and perform cleaning
several times.

6.2.3 Head

cleaning

Is the power turned OFF during ink
replenishment?

Turn the power ON again and continue ink
replenishment.

3.3 Installing ink

cartridges

Occasionally, normal printing cannot
be performed after ink replenishment.

Perform cleaning several times, and check
it each time.

6.2.3 Head

cleaning

No.

Possible cause

Remedy

Reference

Is the power cable connected to the
plug?

Connect the power cable.

3.1 Power cable

connection

Does the AC power supply provide
the specified voltage?

Connect the cable to another outlet.

3.1 Power cable

connection

Is the front cover open or media
loading lever raised?

Close the front cover.
Lower the media loading lever.

3.4 Setting

media

Is the waste fluid box fully inserted?

Fully insert the waste fluid box.

6.1.3 Replacing

waste fluid box

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды