MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 71

Страница: 71 / 186

VJ-1204 OPERATION MANUAL

4 Handling the printer

4-9

4.2.6

Media feed compensation

This section explains the Media feed compensation.

The feeding length depends on the media type. The following or similar results may be seen in prints.

•

Printed images overlap.

•

White lines are printed on images.

The accuracy of media feeding may be improved with the following methods.

1. Display the Media feed compensation menu on the operation panel.

a. Press the [Menu] key on the operation panel.

•

"Menu 1: Setup>" is displayed on the operation panel.

•

The operation panel shifts to the Setup menu display.

b. Press the [>] key on the operation panel.

•

"Set1: MediaType" is displayed on the operation panel.

c. Press the [Enter] key on the operation panel.

•

"Media: Type 1" is displayed on the operation panel.

d. Press the [+] key or [–] key on the operation panel to select the media type to use.

e. Press the [Enter] key on the operation panel.

•

"**>1: Print Mode" is displayed on the operation panel.

TIP

• The selected media (Type 1 to 30) is displayed in "**".

5.1.1 MediaType menu

f. Press the [+] key or [–] key to select "**2: PF Adjust".

g. Press the [>] key on the operation panel.

•

"PF1: Initial Print" is displayed on the operation panel.

•

Proceed to Media feed compensation menu.

5.1.1.1.2 Dist.Adj menu

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды