MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 109

Страница: 109 / 186

VJ-1204 OPERATION MANUAL

5 Panel setup menu

5-25

5.1.17 Longstore menu

Performs cleaning the print head with the cleaning fluid.

NOTE

• Make sure to use a dedicated cleaning fluid (model No.: VJ-MSINK3-CL220).

5.1.18 CR Maintenance menu

Performs maintenance.
Use this for replacing the flushing-box sponge and cleaning the cleaning wiper.

6.1.4 Replacing the flushing-box sponges
6.2.4 Cleaning the cleaning wiper

Setup item

Setting

Description

Longstore

Start

Performs cleaning the print head with the cleaning
fluid.
• [Enter] key:

Perform head cleaning.
The following contents is displayed on the operation
panel.

Remove Cartridges

Remove the ink cartridge, and install the cleaning
cartridge.

6.1.1 Replacing ink cartridges

—

• [Cancel] key: shifts to the previous menu without

cleaning the print head.

5.1 Setup menu

Setup item

Setting

Description

CR Mainte.

Start

Performs maintenance.
• [Enter] key:

The print head moves to center.
The cleaning wiper moves forward.

End

Completes maintenance.
• [Enter] key:

Print head returns to the original position.
The cleaning wiper returns to the original position.

—

• [Cancel] key: shifts to the previous menu without

maintenance.

5.1 Setup menu

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды