MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 36

Страница: 36 / 186

3 Before using

VJ-1204 OPERATION MANUAL

3-10

5. After cleaning the print head is complete, take out the ink cartridge from the bag and shake it gently

two to three times.

•

Slots for ink cartridges are specified depending on the colors of the ink cartridge. Match the
mark on each slot with the color of the ink cartridge.

•

Keep the mark of the ink cartridge facing up and insert it into the slot of the printer.

•

Insert the ink cartridge all the way to the end of the slot.

•

"Ink Refill **%" is displayed on the operation panel and ink replenishment starts.

•

Ink replenishment takes about 4 minutes. Ink filling operation and pause operation are repeated
during the ink replenishment.

•

When "100%" is displayed, the ink replenishment is complete.

NOTE

• Do not perform the following operations during ink filling.

• Do not turn the printer OFF.

• Do not unplug the power cable.

• Do not open the front cover.

• Do not push the media loading lever backward.

•

After the ink replenishment is complete, "Media End" is displayed on the operation panel.

No.

Name

Ink cartridge

Ink cartridge slot K

Ink cartridge slot C

Ink cartridge slot M

Ink cartridge slot Y

2 3 4 5

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды