MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 37

Страница: 37 / 186

VJ-1204 OPERATION MANUAL

3 Before using

3-11

NOTE

• If the printer perform the nozzle check printing immediately after initial ink replenishment is

complete, the following results may occur.

• Printed lines become blurred.

• The data is partially not printed.

In such cases, follow "6.2.3 Head cleaning" and refill a small amount of ink. Then, check the
printing result.

If there is no improvement in the print result even after refill a small amount of ink, leave the
printer unused for an hour or more. Then, refill a small amount of ink again and check the print
result.

If there is still no improvement, contact your local MUTOH dealer.

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды