MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 186

background image

5 Panel setup menu

VJ-1204 OPERATION MANUAL

5-38

5.7.2

Sleep Mode Start menu

Activate Sleep Mode
During Sleep Mode, "Press Enter to restart" will be displayed in the operation panel.
During Sleep Mode, pressing [Enter] key will return the printer to normal operation.

NOTE

• If you try to switch to Sleep Mode under the following circumstances, "Don’t Start Sleep Mode"

will be displayed and the printer will not change to Sleep Mode.

• The front cover is open.

• The media loading lever was switched to the back side.

• The waste fluid tank is full.

• The ink cartridge is empty.

• The ink cartridge has been removed.

• An object other than an appropriate ink cartridge is inserted in the cartridge slot, etc.

Activate Sleep Mode again after returning the printer to a normal state.

7.2 Error messages

• During Sleep Mode, pressing [Enter] key under one of the circumstances listed above will not

return the printer to normal operation.
Return the printer to a normal state, and press [Enter] key to return the printer to normal operation.

7.2 Error messages

Setup item

Setting

Description

Start

Start Sleep Mode?

• [Enter] key: activate Sleep Mode.
• [Cancel] key: shifts to the previous menu without activating

Sleep Mode.

5.7 Sleep Mode menu

Restart -> Enter

During Sleep Mode.
• [Enter] key: return the printer to normal operation.

«
...
120
121
122
123
124
...
»

Содержание ValueJet VJ-1204



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ValueJet VJ-1204

Бренд: Xerox Страницы: 310

Бренд: TallyGenicom Страницы: 38

Бренд: 3D Systems Страницы: 16

Бренд: 3D Systems Страницы: 28

Бренд: 3D Systems Страницы: 21

Бренд: 3D Systems Страницы: 25

Бренд: 3D Systems Страницы: 23

Бренд: 3D Systems Страницы: 35

Бренд: 3D Systems Страницы: 7

Бренд: 3D Systems Страницы: 13

Бренд: 3D Systems Страницы: 19

Бренд: 3D Systems Страницы: 13

Бренд: 3D Systems Страницы: 2

Бренд: 3D Systems Страницы: 2

Cubify CUBEX Duo

Бренд: 3D Systems Страницы: 10

Бренд: 3D Systems Страницы: 7

Бренд: 3DGence Страницы: 24

Бренд: 3DGence Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды