MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 76

Страница: 76 / 186

4 Handling the printer

VJ-1204 OPERATION MANUAL

4-14

4.3

Menu setups on the operation panel

4.3.1

Menu setup procedure

Follow the procedure below to configure each setup menu.

1. Confirm that the operation panel is Normal.

2. Press the [Menu] key on the operation panel.

•

"Menu 1: Setup>" is displayed on the operation panel.

•

The operation panel shifts to the Setup menu display.

3. Press the [+] key or [–] key on the operation panel to select a setup item and press the [Enter] key.

•

The settings will be confirmed.

•

When setup items have a submenu, the display shifts to the next menu.

NOTE

• When a setup item has a submenu, ">" is displayed on the right end of the LCD monitor of the

operation panel.

• For the general outline of each setup item, refer to "4.3.2 Panel setup menu overview".

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды