MUTOH ValueJet VJ-1204 Скачать руководство пользователя страница 151

Страница: 151 / 186

VJ-1204 OPERATION MANUAL

6 Maintenance

6-29

(2) Reinstalling

After moving the printer, follow the procedure below to set it ready for use.

1. Select a suitable place for installation.

Installation manual

2. Move and install the printer to the location.

3. Check the butterfly bolts (2) fixing the stand and the printer are not loosen when using a dedicated

stand.

4. Attach cables, such as the power cable.

3.1 Power cable connection
3.7 Connecting the printer to a PC

5. Perform Nozzle check, and then confirm that there is no clogging in the print head.

3.5.1 Nozzle check

6. Perform Alignment.

3.6 Adjust print

6.3.2

Transporting the printer

When transporting the printer, make sure to pack it in the same condition as purchased, using protective
and packing materials to protect the printer from vibration and shocks.

NOTE

• When transporting the printer, consult the MUTOH product dealer at your point of purchase.

(1) Pre- transport procedure

1. Turn the unit ON.

2. Confirm that the printer functions normally.

3. Remove all ink cartridges.

4. Turn OFF the power of the printer.

•

"Transport Mode" is displayed on the operation panel and the printer starts ejecting ink.

•

Ink rejecting takes about 3 minutes.

5. When ink discharge completes, check that the Power lamp disappears.

6. Remove the scroller.

7. Remove all the cables, such as the power cable.

Содержание ValueJet VJ-1204



























































































































































































Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1204, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1204

Отзывы:

Похожие инструкции для ValueJet VJ-1204

Бренды по названию

Популярные бренды