MQ Power DCA220SSJU4F Скачать руководство пользователя страница 49

Страница: 49 / 80

DCA220SSJU4F 60 HZ GENERATOR• OPERATION MANUAL — REV. #3 (02/10/17) — PAGE 49

MAINTENANCE

AUTO REGENERATION PROCEDURE

Auto regeneration process will automatically occur. No

operator action is required for this process. Allow the engine

to run for at least 30 minutes to complete the automatic

regeneration process.
Reference Table 15 for the various soot level stages for

the DPF system.

NOTICE

Generator derating occurs during soot levels 4 and 5.

Soot level 5 will cause the generator to shutdown If

this condition occurs contact your nearest authorized

service center.

Table 15. Automatic DPF System

Soot Level 0 Soot Level 1 & 2

Soot Level 3

Soot Level 4

Soot Level 5

Controller Message

N/A

FILTER CLEAN

REQUESTED

SOOT LEVEL

HIGH!

SOOT LEVEL

VERY HIGH!

DPF Condition

Regen Not

Required

Moderate Soot

Level

High Soot Level

Very High Soot

Level

Service DPF

(Soot Only)

Pre-Alarm Lamp

N/A

Blinking

Shutdown Lamp

N/A

Engine

Shutdown

NOTICE

DO NOT perform regeneration in conditions where it

may be unsafe due to high exhasust temperatures.

NOTICE

The area above and around the generator during

the regeneration process should be free of any type

of debris, flammable or conbustible materials, as

temperatures during the regeneration process can

reach as high 1,022 °F (550 °C).

REGENERATION (BASLER CONTROLLER)

If a manual regen is needed, the Basler DGC2020 HD

controller will announce a pre-alarm on the controller. The

pre-alarm will state

"NEED MAN REGEN" and "PRESS

RUN BUTTON". While in this condition, pressing the RUN

button for 5 seconds will initiate the Stationary Forced

Regen, it will then display a new pre-alarm "

MAN REGEN

ACTIVE". Once the regen completes, it will automatically

shut down and display "

MAN REGEN COMPLT".

DIAGNOSTIC MODE

There is a feature to put the controller in diagnostic mode.

Diagnostic mode will keep the key switch on for service tool

purposes. To place in diagnostic mode the engine must be

in the off mode.
Press the “Alarm Silence” and the “Lamp Test” buttons at the

same time for 5 seconds. To exit the diagnostic mode you

can press reset, start the engine or turn control power off.

Figure 67. Basler DGC2020 HD Controller

Содержание DCA220SSJU4F

















































































Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды

MQ Power DCA220SSJU4F, Руководство по эксплуатации

Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды