MQ Power DCA220SSJU4F Скачать руководство пользователя страница 25

Страница: 25 / 80

DCA220SSJU4F 60 HZ GENERATOR• OPERATION MANUAL — REV. #3 (02/10/17) — PAGE 25

The definitions below describe the controls and functions

of the Paralleling Panel (Figure 8).
1.

Panel Lights — For operation at night or in dark areas,

panel light illuminates paralleling panel for ease of

reading.

Panel Light Switch — When activated will turn on

control panel light.

Voltage Adjust potentiometer — The

voltage adjust

potentiometer

is a way to adjust the voltage up or

down for fine tuning. The adjustment sends a signal to

the controller to offset the system rated voltage (Trim

Voltage). It is important that all machines are set to the

same value when paralleling.
When first turning on the control power, the controller

will begin its boot sequence much like a computer

does. After completing the boot sequence the unit

will be ready to run or be placed in auto for auto start

applications.

Control Power Toggle Switch — The control power

switch is a master power switch for the digital controller.

The control power switch has a latch feature that

prevents powering down control power while the engine

is running.

Emergency Stop Button Switch — The Emergency

Stop pushbutton switch is used to stop the engine in

case of emergency or to lock out operation during

service. The emergency stop button

should not be

used for routine stopping of the engine

Actuation of the Emergency stop button while the

control power is on will illuminate the light on the button

as well as display “Emergency Stop” on the controller

display. Actuating the Emergency stop button will de-

energize all controller outputs and cause the engine

to stop as well as tripping the circuit breaker. This

condition is a latched condition that must be reset prior

to restarting the engine.
The procedure for resetting the emergency stop

requires several actions. Rotate the emergency stop

button to release the spring latch. To clear the latch,

the controller must be placed into the off mode by

pressing the “OFF” button. While in the “OFF” mode,

the “RESET” button must be pressed to clear the

E-STOP fault.

For units with manual operated breakers, the breaker

will need to be reset by toggling the handle down, then

can be turned back to the “ON” position. On models

with spring charged breakers resetting the breaker is

not necessary.

Contactor Operation (Manual Mode) — The For

manual run applications, user action is required to get

the generator power to the output bus. Depending on

the model, some utilize contactors in series with toggle

handle circuit breakers and others have spring charged

automatic circuit breakers.
On the spring charged types, the buttons on the breaker

itself are not intended for circuit breaker operation.

For instructional purposes both will be referred to as

“contactor”.
There are two pushbuttons on the control panel for

controlling the contactor. There is a green “CLOSE

CONTACTOR” button to close the contactor and a red

“OPEN CONTACTOR” button to open the contactor.

These buttons illuminate to show the contactor status.

If the contactor is open, the red “OPEN CONTACTOR”

button will be illuminated. If the contactor is closed

the green “CLOSE CONTACTOR” button will be

illuminated.
These buttons can sometimes be multifunctional

depending on the situation. For stand-alone operation

the buttons simply close and open the contactor as

expected. For paralleling the buttons can act a little

different.
When the bus is already hot from another generator,

pressing the green online button will initiate a

synchronizing sequence before closing the contactor.

There will be an image of a synchro scope on the

controller display and when the voltage and phases

are matched, the contactor will close.
If there was already load on the bus the unit will slowly

ramp up load until it is sharing equally with the other

generator(s). While sharing load with other generators,

pressing the red “OPEN CONTACTOR” button once

will initiate a ramp down sequence. The unit will begin

to ramp down and when at a low level of load it will

automatically open it contactor. Pressing the red

“OPEN CONTACTOR” button twice will immediately

open the contactor.

PARALLELING PANEL (OPTION)

Содержание DCA220SSJU4F

















































































Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды

MQ Power DCA220SSJU4F, Руководство по эксплуатации

Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды