background image

PAGE 6 — DCA220SSJU4F 60 HZ GENERATOR • OPERATION MANUAL — REV. #3 (02/10/17) 

SAFETY INFORMATION

GENERAL SAFETY

  CAUTION

 

NEVER operate this equipment without proper protective 

clothing, shatterproof glasses, respiratory protection, 

hearing protection, steel-toed boots and other protective 

devices required by the job or city and state regulations.

 

NEVER operate this equipment when not 

feeling well due to fatigue, illness or when 

under medication.

 

NEVER operate this equipment under the infl uence of 

drugs or alcohol.

 

ALWAYS check the equipment for loosened threads or 

bolts before starting.

 

DO NOT use the equipment for any purpose other than 

its intended purposes or applications.

NOTICE

 

This equipment should only be operated by trained and 

qualifi ed personnel 18 years of age and older.

 

Whenever necessary, replace nameplate, operation and 

safety decals when they become diffi cult read.

 

Manufacturer does not assume responsibility for any 

accident due to equipment modifi cations. Unauthorized 

equipment modifi cation will void all warranties.

 

NEVER use accessories or attachments that are not 

recommended by MQ Power for this equipment. Damage 

to the equipment and/or injury to user may result.

 

ALWAYS know the location of the nearest 

fi re extinguisher.

 

ALWAYS know the location of the nearest 

fi rst aid kit.

 

ALWAYS know the location of the nearest 

phone or 

keep a phone on the job site. Also, know the 

phone numbers of the nearest 

ambulance, doctor and 

fi re department. This information will be invaluable in 

the case of an emergency.

GENERATOR SAFETY

  DANGER

 

NEVER operate the equipment in an explosive 

atmosphere or near combustible materials. An 

explosion or fi re could result causing severe 

bodily harm or even death.

  WARNING

 

NEVER disconnect any emergency or safety devices.

 

 

These devices are intended for operator safety. 

Disconnection of these devices can cause severe injury, 

bodily harm or even death. Disconnection of any of these 

devices will void all warranties.

  CAUTION

 

NEVER lubricate components or attempt service on a 

running machine.

NOTICE

 

ALWAYS ensure generator is on level ground before use.

 

ALWAYS keep the machine in proper running condition.

 

Fix damage to machine and replace any broken parts 

immediately.

 

ALWAYS store equipment properly when it is not being 

used. Equipment should be stored in a clean, dry location 

out of the reach of children and unauthorized personnel

Содержание DCA220SSJU4F

















































































Отзывы: