MQ Power DCA220SSJU4F Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 80

background image

PAGE 66 — DCA220SSJU4F 60 HZ GENERATOR • OPERATION MANUAL — REV. #3 (02/10/17)

BASLER DGC-2020 PROGRAMMING APPENDIX (OPTION)

Both buses dead/unstable

One bus stable and the other dead/unstable

Both buses stable

Breaker Closed

Breaker Open and OK to Close

Breaker Open and Not OK to Close

Breaker Open and Close Request Sent

Breaker Closed and Open Request Sent

Breaker Open and Failed to Close

Breaker Closed and Failed to Open

Figure E. One-Line Diagram Breaker and Bus States

Front Panel Shortcuts

Front panel shortcuts allow the user to intuitively view metered bus values and issue breaker commands

by simply selecting components in the one-line diagram.
While viewing the overview screen, press Edit to enable a cursor in the system configuration one-line

diagram. Moving the cursor, by using the left and right arrow keys, selects different components in the

system diagram. A component selected by the cursor is displayed with inverted colors to differentiate it

from the rest.
Select a bus in the diagram with the cursor and press Edit to view metered voltage, current, frequency,

kW, kvar, and power factor values of the corresponding bus in the system.
To send an open or close request to a breaker in the system, move the cursor to the corresponding

breaker in the diagram and press Edit. Press the up or down arrow keys to scroll the options. Press Edit

again to send the selected breaker command request.
The system configuration one-line diagram which is displayed on the overview screen is determined by

the System Type setting selection. For details on configuring the system type, see the

Configuration

chapter.

Scrolled Metering

BESTCOMSPlus

®

Navigation Path:

Settings Explorer, General Settings, Front Panel HMI

Front Panel Navigation Path:

Settings > General Settings > Front Panel HMI

When scrolled metering is enabled, user-selected metering values are displayed on the overview screen.

Any number of the available values can be displayed. Up to nine values are displayed on the screen at

one time. After the scroll time delay has elapsed, the next set of values is displayed and so on.
When scrolled metering is disabled, only the following parameters are displayed on the overview screen:

•

VOLT

∗

•

AMP

∗

•

PH

∗

•

Hz

•

OIL

P0071-91

!

!

«
...
64
65
66
67
68
...
»

Содержание DCA220SSJU4F

















































































Отзывы:

Нет отзывов

Похожие инструкции для DCA220SSJU4F

Бренд: ABB Страницы: 78

Бренд: La Marche Страницы: 21

Бренд: ESI Страницы: 17

CIMR-XC2 Series

Бренд: YASKAWA Страницы: 77

Бренд: Linear Technology Страницы: 22

BLUESTREAM DA44AU

Бренд: Dante Страницы: 12

Бренд: Magtek Страницы: 54

Бренд: Lindy Страницы: 14

Бренд: Majella Страницы: 6

Бренд: Zamp Solar Страницы: 7

Бренд: Parallax Страницы: 3

Бренд: Kramer Страницы: 2

SUNNY BOY 3000-US

Бренд: SMA Страницы: 36

Бренд: Tektronix Страницы: 11

Бренд: Cobalt Digital Inc Страницы: 126

Digi Edgeport/1i

Бренд: Inside Out Networks Страницы: 22

Бренд: StarTech.com Страницы: 11

Бренд: WarmPool Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды