MQ Power DCA220SSJU4F Скачать руководство пользователя страница 65

Страница: 65 / 80

DCA220SSJU4F 60 HZ GENERATOR• OPERATION MANUAL — REV. #3 (02/10/17) — PAGE 65

Tie Breaker and Tie Breaker

Generator Breaker and Tie Breaker

Tie Breaker

Generator Breaker, Group Breaker, and System Bus

Generator Breaker and System Bus

Generator Breaker, Group Breaker, and Mains Breaker

Generator Breaker and Group Breaker

Generator Breaker and Mains Breakers

Generator Breaker

None

Figure D. System Configuration One-Line Diagrams

The diagrams in Figure D show all breakers in the open position and all buses in a dead/unstable state.

Breaker and bus states in the diagram change in real time to reflect the actual breaker and bus status.

When a breaker is open, the line between the contacts is vertical and when the breaker is closed, the line

is horizontal. A stable bus is indicated by a filled rectangle and a bus in any state other than stable is

indicated by an unfilled rectangle. On the optional touch screen, a dead bus is indicated by a green

colored line segment and an energized (failed or stable) is indicated by a red colored line segment. See

Figure E for the different breaker and bus states.

P0071-90

SYS

GG L

BASLER DGC-2020 PROGRAMMING APPENDIX (OPTION)

Содержание DCA220SSJU4F

















































































Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды

MQ Power DCA220SSJU4F, Руководство по эксплуатации

Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды