MQ Power DCA220SSJU4F Скачать руководство пользователя страница 18

Страница: 18 / 80

PAGE 18 — DCA220SSJU4F 60 HZ GENERATOR • OPERATION MANUAL — REV. #3 (02/10/17)

GENERAL PARALLELING INFORMATION (OPTION)

THREE PHASE 480V/208V PARALLEL WIRING VIA

CAMLOCKS

REQUIRED EQUIPMENT

4/0 Single Conductor Cable (User Supplied)

CAT5E Shielded Cable or Better (User Supplied)

Power Distribution Panel (User Supplied)

The following procedure intended to assist the user with

the parallel wiring configuration for the DCA220SSJU4F

generator using the camlok connector panel.

PREPARATION

1.  Make sure generator is turned off and engine is cool.
2.  Disconnect any loads connected to the generator.
3.  Place the main circuit breaker in the

OFF position.

4. Place the generator in an area free of dirt and debris

Make sure it is on secure level ground.

5. Disconnect

negative

battery cable from the battery.

3Ø-480 VAC PARALLEL WIRING CONFIGURATION

1. Using 4/0 cables connect the two generators to the

power distribution panel as referenced in the 3Ø-480V

parallel wiring diagram.

NOTICE

Only a

qualified service technician or licensed

electrician with proper training should perform

this installation. Follow all shop safety rules when

performing this installation.

DANGER

To prevent arcing make sure cables are securely tighten

at power distribution panel, the possibility exist of the

unit catching on fire thus causing equipment damage

and severe bodily harm.

NOTICE

When connecting load cables to the power distribution

panel be sure to select the correct size of the load

cables to handle full load/amperage of both generators

(parallel).

3Ø-208 VAC PARALLEL WIRING CONFIGURATION

1. Using 4/0 cables connect the two generators to the

power distribution panel as referenced in the 3Ø-208V

parallel wiring diagram.

ETHERNET CABLE CONNECTION

1. Connect a CAT5E Ethernet cable (shielded) between

port 1 on both generators as shown in Figure 3.

Figure 3. Ethernet Cable Connection

2. Reference Table 4 for additional Ethernet port

connections.

3. Reconnect battery.
4. Start generator as outlined in start up section of this

manual.

CAT5E ETHERNET

CABLE (SHIELDED)

CAT5E PORT 1

GENERATOR 1

CAT5E PORT 1

GENERATOR 2

PORT 2

Table 4. Ethernet Cable Connections

Generator 1

Generator 2

Port 2

Port 1

Port 2

Содержание DCA220SSJU4F

















































































Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды

MQ Power DCA220SSJU4F, Руководство по эксплуатации

Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды