MQ Power DCA220SSJU4F Скачать руководство пользователя страница 5

Страница: 5 / 80

DCA220SSJU4F 60 HZ GENERATOR• OPERATION MANUAL — REV. #3 (02/10/17) — PAGE 5

SAFETY INFORMATION

Do not operate or service the equipment before reading the

entire manual. Safety precautions should be followed at all

times when operating this equipment. Failure to read and

understand the safety messages and operating instructions

could result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you

about potential hazards that could injure you or others. The

safety messages specifi cally address the level of exposure

to the operator and are preceded by one of four words:

DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided,

COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided,

COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this

equipment will be referenced with hazard symbols which

may appear throughout this manual in conjunction with

safety messages.

Содержание DCA220SSJU4F

















































































Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды

MQ Power DCA220SSJU4F, Руководство по эксплуатации

Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды