MQ Power DCA220SSJU4F Скачать руководство пользователя страница 34

Страница: 34 / 80

PAGE 34 — DCA220SSJU4F 60 HZ GENERATOR • OPERATION MANUAL — REV. #3 (02/10/17)

INSPECTION/SETUP

CIRCUIT BREAKERS

To protect the generator from an overload, a 3-pole, 600

amp, main circuit breaker is provided to protect the

U,V,

and W Output Terminals from overload. In addition two

single-pole, 20 amp

GFCI circuit breakers are provided to

protect the GFCI receptacles from overload. Three 50 amp

load circuit breakers have also been provided to protect

the auxiliary receptacles from overload. Make sure to itch

ALL circuit breakers to the OFF position prior to starting

the engine.

LUBRICATION OIL

Fill the engine crankcase with lubricating oil through the

filler hole, but

DO NOT overfill. Make sure the generator is

level and verify that the oil level is maintained between the

two notches (Figure 31) on the dipstick. See Table 10 for

proper selection of engine oil.

Figure 31. Engine Oil Dipstick

When checking the engine oil, be sure to check if the oil is

clean. If the oil is not clean, drain the oil by removing the

oil drain plug, and refill with the specified amount of oil as

outlined in the

John Deere Owner’s Manual. Oil should

be warm before draining.
Delo® engine oil is the recommended engine oil for this

generator. When replacing engine oil please refill using

Delo® 400 LE SAE 15W-40 (API CJ-4) engine oil.

Table 10. Recommended Motor Oil

FUEL CHECK

Refilling the Fuel System

This generator has an internal fuel tank located inside

the trailer frame and may also be equipped with an

environmental fuel tank (Figure 32).

ALWAYS fill the fuel

tanks with clean fresh

#2 diesel fuel. DO NOT fill the fuel

tanks beyond their capacities.
Pay attention to the fuel tank capacity when replenishing

fuel. The fuel tank cap must be closed tightly after filling.

Handle fuel in a safety container. If the container does not

have a spout, use a funnel. Wipe up any spilled fuel

immediately.

Figure 32. Internal Fuel Tank System

DANGER

Fuel spillage on a

hot engine can cause

fire or explosion. If fuel spillage occurs,

wipe up the spilled fuel completely to

prevent fire hazards.

NEVER smoke

around or near the generator.

CAUTION

ONLY properly trained personnel who have read

and understand this section should refill the fuel tank

system.

Generator Internal Fuel Tank

Trailer Fuel Tank

220

Содержание DCA220SSJU4F

















































































Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды

MQ Power DCA220SSJU4F, Руководство по эксплуатации

Результаты поиска

Содержание DCA220SSJU4F

Отзывы:

Похожие инструкции для DCA220SSJU4F

Бренды по названию

Популярные бренды