Moxa Technologies ioLogik E2210 Скачать руководство пользователя

Страница: 61 / 144

ioLogik E2200 Series

Using ioAdmin

3-30

DNS Settings

Use this field to specify the IP addresses of one or two DNS servers. DNS servers can be used to find available

e-mail addresses when setting up Click & Go rules.

Serial Settings

You can view the reserved RS-485 communication parameters here, and set the timeout value for breaks in

RS-485 communication. Note that the other serial communication parameters cannot be modified. If you wish

to adjust the baudrate, you will need to use the physical dial on the back panel of the ioLogik.

Web Access Settings

This field enables and disables the web console, which allows the ioLogik to be configured from a web browser.

If this field is not enabled, you will not be able to open the web console.

TCP Alive Check Time

The Modbus/TCP Alive Check time is designed to assure TCP connection with the Server. During the specified

time period, the ioLogik will send four packages to the server to check for TCP connection. When the server

does not response within the specified time period ioLogik will automatically release its modbus/TCP connection

to the server. The TCP Alive Check will only be activated again when the connection with the server resumes.

Firmware Update Tab

The

Firmware Update

tab is available after you log in as an administrator. Enter the path to the firmware file

or click on the icon to browse for the file. Click

Update

to update the ioLogik firmware. The wizard will lead you

through the process until the ioLogik has restarted.

ATTENTION

Do not interrupt the firmware update process!

An interruption in the process might result in your device

becoming unrecoverable.

After the firmware is updated, the ioLogik will restart and you will need to log in again to access administrator

functions.

The firmware on any attached I/O expansion module, such as an ioLogik R2100 server, must be updated over

the RS-485 bus. Firmware on cascaded modules cannot be updated over an Ethernet network.

Содержание ioLogik E2210
















































































































































Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды

Moxa Technologies ioLogik E2210, Руководство пользователя

Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды