Moxa Technologies ioLogik E2210 Скачать руководство пользователя

Страница: 56 / 144

ioLogik E2200 Series

Using ioAdmin

3-25

Configuring RTD Input Channels

The ioLogik E2260 provides 6 fixed physical RTD input (Resistance Temperature Detector) channels, each

supporting up to 18 different types including PT50, PT100, JPT100, and more. The RTD channels are numbered

from channel 0 to channel 5. Channels 6 through 11 are virtual temperature channels that report running

averages or deviations of selected RTD channels.

Alias Names

Click the

Alias Name

tab to customize the channel name. You may use names with up to 16 characters. If you

have already set the Alias Name on the I/O Configuration page, the channel name will appear in Click&Go,

Active message, and Web.

The following table is a list of supported sensor types and ranges.

Sensor Type

Degree

Count

Resistance (1 to 2200)

1 to 2200 Ω

10 to 22000

Resistance (1 to 1250)

1 to 1250 Ω

20 to 25000

Resistance (1 to 620)

1 to 620 Ω

50 to 31000

Resistance (1 to 310)

1 to 310 Ω

100 to 31000

PT50, 0.00385

-200 to 850°C

-328 to 1562°F

-2000 to 8500

PT100, 0.00385

-200 to 850°C

-328 to 1562°F

-2000 to 8500

PT200, 0.00385

-200 to 850°C

-328 to 1562°F

-2000 to 8500

PT500, 0.00385

-200 to 850°C

-328 to 1562°F

-2000 to 8500

PT1000, 0.00385

-200 to 350°C

-328 to 662°F

-2000 to 3500

JPT100, 0.003916

-200 to 640°C

-328 to 1184°F

-2000 to 6400

JPT200, 0.003916

-200 to 640°C

-328 to 1184°F

-2000 to 6400

JPT500, 0.003916

-200 to 640°C

-328 to 1184°F

-2000 to 6400

JPT1000, 0.003916

-200 to 350°C

-328 to 662°F

-2000 to 3500

Ni100, 0.00618

-60 to 250°C

-76 to 482°F

-600 to 2500

Ni200, 0.00618

-60 to 250°C

-76 to 482°F

-600 to 2500

Ni500, 0.00618

-60 to 250°C

-76 to 482°F

-600 to 2500

Ni1000, 0.00618

-60 to 180°C

-76 to 356°F

-600 to 1800

Ni120, 0.00672

-80 to 260°C

-112 to 500°F

-800 to 2600

The status of attached sensors will be reported by the count value, which corresponds to the sensor ranges

shown above. For example, for a 100 mΩ resistor, a count value of 10 corresponds to a 1 Ω reading. M

oxa can

only guarantee accuracy within the ranges shown above. Be sure to verify the sensor type. Accurate readings

beyond these ranges cannot be guaranteed.

Содержание ioLogik E2210
















































































































































Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды

Moxa Technologies ioLogik E2210, Руководство пользователя

Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды