Moxa Technologies ioLogik E2210 Скачать руководство пользователя

Страница: 58 / 144

ioLogik E2200 Series

Using ioAdmin

3-27

Virtual Channels

The ioLogik E2262 provides virtual channels so you can easily determine the average or deviation values for

any attached temperature sensor. A virtual channel can operate in Average Mode or Deviation Mode. In

Average Mode, up to 8 physical channels are selected and the virtual channel reports the average value of the

selected channels. In Deviation mode, two physical channels are selected and the virtual channel reports the

difference between the channels.

When using virtual channels, if there are errors on any of the selected physical channels, that channel’s

readings will simply be ignored. You can refer to the LED indicators to see if any errors are encountered with

any of the physical channels.

Note that virtual channels only support temperature units and cannot be used with resistance units. Any

channel that is connected to a mV voltage input will be treated as an error channel.

Calibration

The ioLogik E2262 allows you to calibrate the TC sensor by user. In each channel configuration section, click

“Calibration” and then follow the onscreen instructions to start the TC sensor calibration. Each calibration needs

about 20 seconds (per channel). Note that you can press “Reset to default” on the Navigation Panel to reload

the factory default value and ignore the user calibrated value. The default value is calibrated in the factory and

is stored in the device.

Alias Name

Click the Alias Name tab to customize the channel name. You may use names with up to 16 characters. If you

already set the Alias Name on I/O Configuration page, the channel name will appear on Click&Go, Active

message, and Web.

Содержание ioLogik E2210
















































































































































Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды

Moxa Technologies ioLogik E2210, Руководство пользователя

Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды