motortronics VMX-Synergy Plus страница 66 Скачать руководство пользователя

Страница: 66 / 143

Operation

5.9 Advanced Menu (continued)

PNU 53807

Advanced

Trip Settings

↓

L1-L3-L2 Trip

Determines if supply phase

sequence is incorrect for motor

rotation.
On: Trips if the phase

sequence is L1-L3-L2.
Off: The unit will not trip

regardless of motor rotation.

Off

Read/Write

PNU 53804

Advanced

Trip Settings

↓

Remote Start Trip

For safety reasons the Unit will

trip during some operations if

the remote start signal is

active.
On: Trips if the remote start

signal is active when the Unit

is powered up or a reset is

applied.
Off: The Unit will not trip and

may start unexpectedly if the

start signal is accidently left

active.

Off

Read/Write

PNU 53775

Advanced

Trip Settings

↓

Current Sensor Trip

Detects if the internal current

sensors have failed or reading

a very low level.
On: The Unit will trip if the

internal current sensors fail or

the current measured falls to a

very low level.
Off: Will continue to operate

even if the sensor has failed.

Measurements and overload

protection may be affected.

Off

Read/Write

PNU 53782

Advanced

Trip Settings

↓

Fan Trip

Detects if the cooling fans

have failed.
On: The Unit trips if the cooling

fans fitted to the Unit fail.
Off : The unit will continue to

operate and is likely to trip on

a thermal trip as the heatsink

will not be sufficiently cooled

Off

Read/Write

Menu

Description

Min

Max

Default

Unit Reg. Type

Содержание VMX-Synergy Plus
















































































































































Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды

motortronics VMX-Synergy Plus, Руководство пользователя

Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды