manualshive.com logo in svg

motortronics VMX-Synergy Plus, Руководство пользователя, Страница: 96 / 143

Поделиться
Скачать
motortronics VMX-Synergy Plus Скачать руководство пользователя страница 96

Operation 

96 

5.12 Log Menu (continued)

Menu 

Description 

Min 

Max 

Default  Unit  Reg. Type 

PNU - 

Log 

Trip Log 

Trip Code Descriptions 

401 

Motor Side Phase Loss 

One or all of the phases are 

missing on the motor side 

during the instant of start up. 
T1 T2 or T3 phase are missing 

or at a very low level. 
Check that the motor is 

connected to T1 T2 and T3. 

Ensure any disconnecting 

device between the Unit and 

the motor is closed at the 

instant of start. 

Read Only 

PNU - 

Log 

Trip Log 

Trip Code Descriptions 

402-403

Motor Side Phase Loss 

One or all of the phases are 

missing on the motor side 

during the instant of start up 

when the motor being 

controlled. 
T1 T2 or T3 phase are missing 

or at a very low level. 
Check all incoming and 

outgoing connections. 

Read Only 

PNU - 

Log 

Trip Log 

Trip Code Descriptions 

601 

Control Voltage Too 

Low 

The internal control supply of 

the Unit level has fallen to a 

low level. 
Can be caused by a weak 

24Vdc control supply. 
Ensure 24Vdc supply meets 

the requirements specified in 

the Quick Start Guide. 

Read Only 

PNU - 

Log 

Trip Log 

Trip Code Descriptions 

701-710

Sensing Fault Trip 

One or more of the internal 

control thyristors (SCRs) have 

failed to turn on properly. 
The Unit has detected that the 

SCRs are not operating as 

expected. 
Check connections all 

incoming and outgoing 

connections. 

Read Only 

PNU - 

Log 

Trip Log 

Trip Code Descriptions 

801-802

Fan Problem 

One or more of the internal 

cooling fans has failed. 
To ensure the heatsink is 

cooled sufficiently the Unit will 

trip if the fans fail to operate. 
Check Unit fans for signs of 

damage or contamination. 

Read Only 

Содержание VMX-Synergy Plus
















































































































































Отзывы:

Нет отзывов