motortronics VMX-Synergy Plus страница 64 Скачать руководство пользователя

Страница: 64 / 143

Operation

5.9 Advanced Menu (continued)

Description

Min

Max

Default

Unit Reg. Type

PNU 44864

Advanced

Trip Settings

↓

Trip Sensitivity

Adjusts the reaction time to

fault trips.
Increase "Trip Sensitivity" to

slow the response to fault

trips.
Sometimes useful on sites

where electrical noise is

causing nuisance tripping.
This is a global setting.

Increasing "Trip Sensitivity"

will slow the response of

nearly all the trips.

100

Read/Write

PNU 53765

Advanced

Trip Settings

↓

Keypad Trip

Detects if the communications

bus has failed or become

inactive between the keypad

and the main unit.
On :Keypad trip enabled.
Off : Keypad trip disabled.

Off

Read/Write

PNU 53793

Advanced

Trip Settings

↓

Shearpin Trip

The shearpin is an electronic

equivalent of a mechanical

shearpin.
On : The Unit will trip. This

feature is not active during soft

start, dwell period and soft

stop.
Off: The Unit will continue to

operate regardless of motor

current level.

Off

Read/Write

PNU 53792

Advanced

Trip Settings

↓

Overload Trip

The Unit has an "Overload"

function that is an electronic

equivalent to a thermal

overload.
On: The Unit will trip when the

"Overload" capacity

(ModbusPNU 33408) exceeds

100%.
Off: The Unit will continue to

operate regardless of motor

current level.

Off

Read/Write

Содержание VMX-Synergy Plus
















































































































































Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды

motortronics VMX-Synergy Plus, Руководство пользователя

Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды