motortronics VMX-Synergy Plus страница 74 Скачать руководство пользователя

Страница: 74 / 143

Operation

5.9 Advanced Menu (continued)

PNU 20813

Advanced

Auto Reset

Reset Trips

Overload

Allows the user to select

whether the unit will auto reset

if an Overload Trip occurs.
On: The trip will auto reset

when the Reset Delay reaches

zero.
Off: The trip will not auto reset.

Off

Read/Write

PNU 20803

Advanced

Auto Reset

Reset Trips

Thyristor Firing

Allows the user to select

whether the unit will auto reset

if a Thyristor Firing Trip occurs
On: The trip will auto reset

when the Reset Delay reaches

zero.
Off: The trip will not auto reset.

Off

Read/Write

PNU 20807

Advanced

Auto Reset

Reset Trips

Sensing Fault

Allows the user to select

whether the unit will auto reset

if a Sensing Fault Trip occurs.
On: The trip will auto reset

when the Reset Delay reaches

zero.
Off: The trip will not auto reset.

Off

Read/Write

PNU 20802

Advanced

Auto Reset

Reset Trips

Thermal

Allows the user to select

whether the unit will auto reset

if a Thermal Trip occurs
On : The trip will auto reset

when the Reset Delay reaches

zero.
Off : The trip will not auto

reset

Off

Read/Write

PNU 20811

Advanced

Auto Reset

Reset Trips

Low Current

Allows the user to select

whether the unit will auto reset

if a Low Current Trip occurs.
On: The trip will auto reset

when the Reset Delay reaches

zero.
Off: The trip will not auto reset.

Off

Read/Write

PNU 20812

Advanced

Auto Reset

Reset Trips

Current Limit Time Out

Allows the user to select

whether the unit will auto reset

if a Current Limit Time Out Trip

occurs.
On: The trip will auto reset

when the Reset Delay reaches

zero.
Off: The trip will not auto reset.

Off

Read/Write

Содержание VMX-Synergy Plus
















































































































































Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды

motortronics VMX-Synergy Plus, Руководство пользователя

Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды