motortronics VMX-Synergy Plus страница 101 Скачать руководство пользователя

Страница: 101 / 143

Operation

101

5.12 Log Menu (continued)

Menu

Description

Min

Max

Default Unit Reg. Type

PNU -

Log

Trip Log

Trip Code Descriptions

2401-2499

Operation 2 Trip

Fail Safe operation (Operation

2)
A process associated with the

Main micro controller has been

affected and is unable to

recover automatically
The trip MUST be reset by

either the digital input or

keypad or the bus command

depending on the control

method set.
This trip is a special case and

it is NOT possible to reset this

trip by cycling the control

supply

Read Only

PNU -

Log

Trip Log

Trip Code Descriptions

2601-2699

Operation 1 Trip

Fail Safe operation (Operation

1)
A process associated with the

Logging function has been

affected and is unable to

recover automatically

The trip can be reset by either

the digital input or keypad or

the bus command depending

on the control method set.

It is also possible to reset this

trip by cycling the control

supply

Read Only

PNU -

Log

Trip Log

Trip Code Descriptions

2701-2799

MPU Trip

Internal Unit Failure (MPU /

Operation 5)
The Unit has failed internally

and is unable to recover

automatically.
Cycle the control supply.
If the fault is not cleared then

contact the supplier

Read Only

PNU 38400

Log

Trip Log

↓

Last Peak Current

Displays the peak current of

the last successful start.

10000

Read Only

Содержание VMX-Synergy Plus
















































































































































Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды

motortronics VMX-Synergy Plus, Руководство пользователя

Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды