motortronics VMX-Synergy Plus страница 111 Скачать руководство пользователя

Страница: 111 / 143

Operation

111

5.13 Device Menu (continued)

Menu

Description

Min

Max

Default

Unit Reg. Type

PNU 16000

Device

Networks

Modbus Network

Settings
Address

Sets the Modbus station

number

Read/Write

PNU 16064

Device

Networks

Modbus Network

Settings

Baud Rate

Sets the serial

communications baud rate.
The available baud rates are

9600 19200 38400 57600 or

115200.

9600

115200

19200

Read/Write

PNU 16128

Device

Networks

Modbus Network

Settings

Parity

Sets the serial

communications parity bit.
The available parity options

are None Even Odd.
Also sets the stop bits. No

parity uses 2 stop bits. Odd or

even parity uses 1 stop bit.

None

Odd

Even

Read/Write

PNU 14080

Device

Networks

Modbus Network

Settings

Traffic LEDS

Allows the user to check the

state of the modbus

communication network.
Red LED receive. Green LED

Transmit.
On: The Red and Green LEDS

display the traffic on the

Modbus communications

network.
Off: The Red and Green LEDs

display the Unit status

information.

Off

Read/Write

PNU -

Device

Networks

↓

Anybus

Anybus expansion module.
Only active with Anybus

module fitted.

Read Only

Содержание VMX-Synergy Plus
















































































































































Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды

motortronics VMX-Synergy Plus, Руководство пользователя

Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды