motortronics VMX-Synergy Plus страница 62 Скачать руководство пользователя

Страница: 62 / 143

Operation

5.9 Advanced Menu (continued)

Description

Min

Max

Default Unit Reg. Type

PNU 25668

Advanced

↓

Motor Protection

↓

Overload Settings

↓

Trip Class Run Value

This feature is only available for ANSI

models.
When selected it allows a different

overload class to be selected during the

running period.
The trip time depends on the selected

run trip class value, the duration of the

overload and the level of the

overcurrent.

Trip

Class

Trip

Class

Trip

Class

Read/Write

PNU 7360

Advanced

iERS

↓

Dwell Time

The time from the End of the start to the

point where the iERS saving mode

becomes active.
Normally set to 5 seconds to ensure the

motor is at full speed before the iERS

saving becomes active,
Increase to allow time for the motor to

stabilise.

300

Read/Write

PNU 21184

Advanced

iERS

↓

iERS Rate

Determines the rate at which the load is

regulated during the iERS energy saving

mode.
During periods of instability the "Current

Irms" and "True Power Factor" will

oscillate rapidly.
Increase if the application shows signs

of instability.
Reduce to increase the speed of

response.

100

Read/Write

Содержание VMX-Synergy Plus
















































































































































Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды

motortronics VMX-Synergy Plus, Руководство пользователя

Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

Похожие инструкции для VMX-Synergy Plus

Бренды по названию

Популярные бренды