manualshive.com logo in svg

TECO JSDE Series, Руководство пользователя, Страница: 1 / 62

Поделиться
Скачать
TECO JSDE Series Скачать руководство пользователя страница 1

1                                             

 

■

Warning and Alert:

 

Warning 

y

 

Do not proceed to the assembly of the line while electrifying. 

y

 

Before doing any maintenance or repair always wait until CHARGE LED goes off and supply 
power is totally separation from the drive.   

y

 

The output terminal of Servo drive [U, V, W] must NOT touch the AC power.

 

 

Alert 

y

 

Install the cooling fan for the Servo drive while the environment temperature is too high. 

             

Ex. Servo driver is installed in the control panel. 

 

y

 

Do not proceed to the Anti-Pressure-Test to the Servo driver.

 

y

 

Confirm the quick stop function is available before operate servo drive. 

 

y

 

Matching up machine to change the user parameter setting before machine performs. If there is 

no according correct setting number, it could lead to out of control or breakdown. 

 

 

  Safety proceeding:

 

Check the covering letter detail before installing, running, maintaining and examining. Furthermore, only 

the profession-technician can proceed to assemble and repair. 

Safety proceeding in the covering letter discriminate between “Warning” & ”Alert”. 

 

 

Indicating the possibility dangerous situation. It could cause the death or serious   

damage if being ignored. 

 

 

Indicating the possibility dangerous situation. It could cause smaller or lighter human 

injured and damage of equipment

.  

 

Read this covering letter detail before using Servo driver.

 

 

Alarm 

Warning 

!

 

!

Содержание JSDE Series































































Отзывы:

Нет отзывов