motortronics VMX-Synergy Plus Скачать руководство пользователя страница 129

Страница: 129 / 143

Trip and Fault Codes

129

6.2.2 Logging Operation 2 Trip (2601 – 2603)

Trip numbers that are in the range of 2601 to 2603 indicate that a process associated with the

logging has been affected in some way and has been unable to recover automatically.

•

The trip is turned ON and OFF via the “Logging Trip” (Advanced/Trips).

•

The default for this trip is OFF.

•

With the trip OFF, the logging function will temporarily be disabled if a continual failure is

detected.

•

When the trip is turned ON, it is reset using either the digital input or keypad or bus

command, depending on the control method set.

•

It is possible to reset this trip by cycling the control supply.

Code

Description

2601 The initialization of the event logging function has been unsuccessful for 20 consecutive

attempts.

2602 The event logging function has been unsuccessful for 20 consecutive attempts.
2603 The SD card could not be accessed after 20 consecutive attempts.

Содержание VMX-Synergy Plus
















































































































































Результаты поиска

Содержание VMX-Synergy Plus

Отзывы:

motortronics VMX-Synergy Plus, Руководство пользователя, Страница: 129 / 143

Результаты поиска

Содержание VMX-Synergy Plus

Отзывы: