MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 212 | Manualshive

Страница: 212 / 290

background image

Shock absorbers

Adjusting

The rear suspension consists of a spring-shock

absorber unit linked to the frame via Silent-block

and to the rear fork via a linkage system.

To set vehicle suspension, the shock absorber

has:

- a set screw (1) to adjust the hydraulic rebound

damping;

- a set knob (2) to adjust spring (3) preloading.

Standard rear shock absorber setting is adjusted

to suit most high and low speed riding conditions,

to transport the rider plus luggage.

However, this set can be modified for specific

needs according to vehicle use.

ALLOW ENGINE AND EXHAUST SILENCER TO COOL OFF
BEFORE OPERATING THE SET SCREWS.

ADJUSTMENTS

Regular adjustment (standard):

- only rider.

Half load adjustment:

- (for example, rider with passenger or with luggage).

Maximum load adjustment:

- (for example, rider, passenger and luggage).

CAUTION

SET SPRING PRELOADING AND SHOCK ABSORBER REBOUND DAMPING ACCORDING TO
THE VEHICLE USE CONDITIONS. IF THE SPRING PRELOADING IS INCREASED, IT IS NECES-
SARY TO INCREASE THE REBOUND DAMPING ACCORDINGLY TO AVOID SUDDEN JERKS
WHEN RIDING. IF NECESSARY, CONTACT AN Official Moto Guzzi Dealer. TRY RIDING THE VE-
HICLE ON THE STREET UNTIL THE OPTIMUM ADJUSTMENT IS OBTAINED.

SHOCK ABSORBER SETTING TABLE

Regular load adjustments are the standard settings by manufacturer

REAR SHOCK ABSORBER ADJUSTMENT (1)

Specification

Desc./Quantity

Preload - regular load conditions

15 clicks starting from knob (2) fully loosened

Preload - half-load conditions

28 clicks starting from knob (2) fully loosened

Preload - maximum load conditions

33 clicks starting from knob (2) fully loosened

Rebound - regular load conditions

24 clicks starting from screw (1) fully tightened

Suspensions

Stelvio 1200 NTX ABS

SUSP - 212

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

«
...
210
211
212
213
214
...
»

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stelvio 1200 NTX

Бренд: R&G Страницы: 6

Бренд: VEB Страницы: 63

2016 Empulse TT

Бренд: Victory Motorcycles Страницы: 138

Бренд: Suzuki Страницы: 26

Бренд: R&G Страницы: 6

Бренд: Kabuto Страницы: 20

Бренд: oset Страницы: 44

SPORTTOURING ST4S

Бренд: Ducati Страницы: 313

Бренд: PMI Страницы: 2

Бренд: DYNATEK Страницы: 4

Бренд: TERMOSCUD Страницы: 16

Бренд: Sealey Страницы: 4

CIAK MASTER 50-4T

Бренд: Malaguti Страницы: 31

Kawasaki NINJA 650

Бренд: Arrow Страницы: 7

MicroFlooter 8500220

Бренд: Wunderlich Страницы: 2

Бренд: Honda Страницы: 230

CRF1000 Africa Twin

Бренд: Honda Страницы: 375

Himalayan BS IV 2018

Бренд: Royal Enfield Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды