MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 159

Страница: 159 / 290

•

Fit the gasket with the correct thick-

ness between the head and the cylin-

der.

•

Fit the right cylinder head.

•

Unscrew and remove the right chain

tensioner cap.

•

Screw two screws in the threaded

holes of the timing system upper gear.

•

Rotate the camshaft so that its pin is

aimed towards the hole in the timing

system chain.

•

Place the gear in the chain.

•

On the right camshaft pin, fit the hole

marked with the letter "R" of the timing

system gear.

•

Screw the cap of the right chain ten-

sioner.

•

Undo and remove the screws used to

place the gear on the camshaft.

•

Place the bulkhead and align the holes

with the timing system gear.

•

Fix the bulkhead on the timing system

gear using a screw with Loctite on the

thread.

•

Tighten the screw to the prescribed tor-

que.

•

Also place the bulkhead of the other

head.

Stelvio 1200 NTX ABS

Engine

ENG - 159

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды