MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 82

Страница: 82 / 290

If a short circuit to ground is detected at PIN 10 of the instrument panel connector, the display will show

a full scale temperature indication of 60°C

Check the ground insulation of the sensor connector pink cable: if there is a connection, restore the

cable harness; if it is earth insulated, check that sensor resistance is correct: if it is not OK, replace the

sensor; if it is OK, replace the instrument panel.

RUN/STOP switch

Function

It tells the control unit if the driver wishes to enable engine start-up or to keep the engine running.

Operation / Operating principle

If the driver wants to shut off the engine or to disable engine start-up, the switch should be open, i.e.

the Marelli control unit should not detect voltage at PIN 27 of the BLUE connector.

Level in wiring diagram:

Start-up enabling switches.

Location:

•

right light switch.

•

connector: right side, near the coil.

Electrical characteristics:

•

STOP position: the circuit is open

•

RUN position: closed circuit (continuity)

PIN:

•

sky blue/orange cable: 0V if engine kill in STOP; 12V if engine kill in RUN

•

red/black cable: voltage 12V

AXONE: STATUSES

Run / stop switch

Example value

:Run/Stop

DIAGNOSIS

•

Indication on Axone always STOP: disconnect the connector and, with the switch set to

RUN, check if there is continuity towards the switch of both the sky blue/green and the grey/

sky blue cables (sensor side): if there is not continuity, replace the sensor; if there is, check

the connector. If it is not OK, restore the cable harness; if it is OK, with the key set to ON,

check if there is voltage on the red/black cable (cable harness side): if there is no voltage,

restore the cable harness; if there is, check the ground insulation of the sky blue/orange

cable (cable harness side): if there is continuity to ground, restore the cable harness; if it is

OK, take the key to OFF and check that the BLUE connector is in good conditions and if

there is continuity of the sky blue/orange cable between the connector in question and PIN

Electrical system

Stelvio 1200 NTX ABS

ELE SYS - 82

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды