MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 134

Страница: 134 / 290

•

Unscrew and remove the four head

cover fixing screws and collect the

sealing O-rings.

•

Remove the head cover together with

the gasket.

Removing the cylinder head

CAUTION

WHEN REMOVING THE COMPONENTS, MARK THE POSITION OF EACH PART VERY CARE-
FULLY IN ORDER TO PLACE THEM IN THEIR ORIGINAL POSITION UPON FITTING.

•

Remove the head cover.

•

Unscrew and remove the two screws

•

Remove the cap.

•

Unscrew and remove the screw.

•

Remove the timing system upper gear

bulkhead.

For the right head:

•

Unscrew and remove the chain ten-

sioner cap.

•

Remove the right chain tensioner.

Engine

Stelvio 1200 NTX ABS

ENG - 134

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды