manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 145

•

Fit the timing chains according to the

references marked at the removal

phase.

•

Lubricate the service shaft.

•

Insert the service shaft in its crankcase

seat by sliding it through the two

chains.

•

Fit each chain to the corresponding

service shaft gear.

•

Fit the roller cage and a new O-ring on

the service shaft closing cap.

•

Partially fit the service shaft closing

cap.

•

To screw the cap until it stops, use two

M6 flanged screws larger than the orig-

inal screws.

•

Tighten the two M6 flanged screws op-

erating in stages until the cap stops

against the crankcase.

•

Undo and remove the two M6 flanged

screws.

•

Tighten the cap with the two original

TBEI screws.

Stelvio 1200 NTX ABS

Engine

ENG - 145

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды