MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 290

background image

Gearbox Oil

Inspection

CHECKING AND TOPPING UP

CAUTION

ENGINE MUST BE WARM TO CHECK GEARBOX OIL LEVEL.

NOTE

DO NOT LET THE ENGINE IDLE WITH THE VEHICLE AT STANDSTILL TO WARM UP THE ENGINE
AND REACH THE OPERATING TEMPERATURE OF ENGINE OIL. OIL IS BEST CHECKED AFTER
RUNNING FOR ABOUT 15 KM (10 miles).

•

Shut off the engine.

•

Keep the vehicle upright with both

wheels on the ground.

•

Unscrew and remove the cap/dipstick

(1) placed on the gearbox right side.

•

• The level is correct if the oil is on the

rim of the hole of the cap/dipstick (1).

If necessary:

•

Top-up with oil until it reaches the dip-

stick opening (1).

CAUTION

DO NOT ADD ADDITIVES OR ANY OTHER SUBSTANCE TO
THE FLUID. WHEN USING A FUNNEL OR ANY OTHER EL-
EMENT, MAKE SURE IT IS PERFECTLY CLEAN.

Replacement

NOTE

HOT OIL IS MORE FLUID AND WILL DRAIN OUT MORE EASILY AND COMPLETELY.

• Place a container with suitable capacity under the

drainage plug (2).

• Unscrew and remove the drainage plug (2).

• Unscrew and remove the filler cap (1).

• Drain the oil into the container; allow several mi-

nutes for oil to drain out completely.

• Check and replace, if necessary, the sealing

washers of drainage plug (2).

• Remove any metal scrap attached to the drain-

age plug (2) magnet.

• Screw and tighten the drainage plug (2).

Maintenance

Stelvio 1200 NTX ABS

MAIN - 36

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

«
...
34
35
36
37
38
...
»

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stelvio 1200 NTX

Бренд: Free Spirits Страницы: 32

Бренд: hepco & becker Страницы: 6

Powersports CT200U

Бренд: Coleman Страницы: 37

Бренд: B-PWR Страницы: 13

Бренд: R&G Страницы: 6

Mesh Helmet Cover

Бренд: Ops-Core Страницы: 2

Бренд: GAS GAS Страницы: 74

HUSABERG MX 2000

Бренд: Ohlins Страницы: 16

Бренд: hepco & becker Страницы: 2

Бренд: OKBABY Страницы: 35

Бренд: BOXER Страницы: 11

Бренд: PIAGGIO Страницы: 275

Бренд: ESAB Страницы: 4

MOTO NOSTRA MN4602

Бренд: SC Страницы: 8

Бренд: Caberg Страницы: 28

Бренд: Yamaha Страницы: 120

Бренд: DYNATEK Страницы: 4

Бренд: Shark Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды