manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 34

Engine oil

Check

CAUTION

ENGINE MUST BE WARM TO CHECK ENGINE OIL LEVEL

NOTE

DO NOT LET THE ENGINE IDLE WITH THE VEHICLE AT STANDSTILL TO WARM UP THE ENGINE
AND REACH THE OPERATING TEMPERATURE OF ENGINE OIL. OIL IS BEST CHECKED AFTER
RUNNING FOR ABOUT 15 KM (10 miles).

•

Stop the engine.

•

Keep the vehicle upright with both wheels on the ground.

•

Pull the filler plug / oil level dipstick (1)

straight out.

•

Wipe the oil level dipstick (1) clean and

reinsert it.

•

Pull it out again and check the oil level.

•

The oil level is correct when it is close

to the "MAX" mark. Otherwise, top-up

with engine oil.

CAUTION

DO NOT ADD ADDITIVES OR OTHER SUBSTANCES TO THE OIL. WHEN USING A FUNNEL OR
ANY OTHER ELEMENT, MAKE SURE IT IS PERFECTLY CLEAN.

Replacement

NOTE

HOT OIL IS LESS VISCOUS AND WILL DRAIN OUT MORE EASILY AND COMPLETELY.

It is necessary to remove the metal oil sump guard

in order to change the engine oil and replace the

oil filter:

•

Operating from both sides, unscrew

and remove both screws (1).

•

Remove the oil sump guard.

Maintenance

Stelvio 1200 NTX ABS

MAIN - 34

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды