MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 290

MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 14

Wheels and tyres

WHEELS AND TYRES - STELVIO NTX

Wheel

Model

Wheel rim

Measure

ment

Tyre pressure with

rider only

Tyre pressure, rider +

passenger

Front (standard)

Metzeler Tourance

2.50 x 19"

110/80

R19 - 59V

2.4 bar (240 kPa) (34.8

PSI)

2.5 bar (250 kPa) (36.3

PSI)

Front (alternative)

Metzeler Karoo (*) (***)

2.50 x 19"

110/80

R19 - 59R

M+S

2.5 bar (250 kPa) (36.3

PSI) (**)

2.5 bar (250 kPa) (36.3

PSI) (**)

Front (alternative)

Pirelli Scorpion Sync

2.50 x 19"

110/80

R19 - 59V

2.5 bar (250 kPa) (36.3

PSI)

2.5 bar (250 kPa) (36.3

PSI)

Rear (standard)

Metzeler Tourance

4.25 x 17"

150/70

R17 - 69V

2.7 bar (270 kPa) (36.1

PSI)

2.9 bar (290 kPa) (42.1

PSI)

Rear (alternative)

Metzeler Karoo (*) (***)

4.25 x 17"

150/70

R17 - 69R

M+S

2.7 bar (270 kPa) (36.1

PSI) (**)

2.9 bar (290 kPa) (42.1

PSI) (**)

Rear (alternative)

Pirelli Scorpion Sync

5.50 x 17

180/55

R17 - 73V

2.9 bar (290 kPa) (42.1

PSI)

2.9 bar (290 kPa) (42.1

PSI)

(*) Maximum speed limit = 170 km/h (105 mi/h).

(**) Tyre pressure must be adjusted to suit terrain conditions for off road use.

(***) Do not install on vehicles equipped with ABS

WHEN FITTING Metzeler Karoo TYRES, THE MAXIMUM SPEED WARNING LABEL (INCLUDED
WITH TYRES) MUST BE APPLIED TO THE SPEEDOMETER. USE EXTREME CAUTION WHEN
RIDING ON TARMAC ROADS WITH "OFF-ROAD / ALLROUND" TYRES AS THESE TYRES OFFER
POOR GRIP AND STABILITY ON TARMAC.

DO NOT INSTALL M+S TYPE TYRES ON VEHICLES EQUIPPED WITH ABS.

Supply

FUEL SYSTEM

Specification

Desc./Quantity

Fuel system

Electronic injection (Weber . Marelli) with Stepper motor

Diffuser

diameter: 50 mm (1.97 in)

Fuel

Premium unleaded petrol, minimum octane rating 95 (NORM)

and 85 (NOMM)

Tightening Torques

HEADS

Name

Torque in Nm

Oil cap (2)

25 Nm (18.44 lbf ft)

Rocking lever support nut - M10x1.5 (8)

15 Nm (11.06 lbf ft) + 42 Nm (30.98 lbf ft)

Camshaft - rocking levers support fixing screws (12)

17 Nm (12.54 lbf ft)

Head fixing screw (4) - pre-tightening

15 Nm (11.06 lbf ft)

Head fixing screw (4) - final tightening

42 Nm (31 lbf ft)

Screw fixing head to chain compartment - M6x120 (4)

10 Nm (7.38 lbf ft)

Oil temperature sensor

11 Nm (8.11 lbf ft) - Loctite 243

Oil temperature sensor container

11 Nm (8.11 lbf ft) - Loctite 601

Characteristics

Stelvio 1200 NTX ABS

CHAR - 14

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

«
...
12
13
14
15
16
...
»

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды