MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 167

Страница: 167 / 290

•

Place the flywheel-side flange on the

crankshaft and check if the dowel pin

with the O-ring is correctly placed.

•

When fitting the flange on the crank-

case, make sure that the three dowel

pins match the seats on the crankcase.

•

Apply Teflon tape on the two lower fix-

ing screws at the back in order to pre-

vent oil leaks.

•

Screw the eight flange screws on the

flywheel side proceeding diagonally.

•

Remove the sealing ring centring tool from the crankshaft.

Specific tooling

12.91.20.00

Tool to fit the flywheel-side flange together with sealing ring on the crankshaft

•

To avoid that the shim washer inside

the crankcase moves out of its seat, fit

the two gears and the nut on the crank-

shaft on the generator side.

Stelvio 1200 NTX ABS

Engine

ENG - 167

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Результаты поиска

Содержание Stelvio 1200 NTX

Отзывы:

Похожие инструкции для Stelvio 1200 NTX

Бренды по названию

Популярные бренды