manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 185

If there is a larger difference:

•

act on the set screw of the throttle body

connecting rod to reduce the pressure

difference in the two pipes.

•

Repeat the procedure "Throttle posi-

tion self-learning" as explained above.

•

Bring the engine back to idle and check

the depression values so that they are

aligned between the two cylinders.

•

Otherwise, open only the screw with

higher depression, using the by-pass

screws, to compensate.

Recovery function

If the signal of the following sensors is interrupted, the control unit determines some values to keep the

engine running or it uses a different parameter. The instrument panel and the Axone also signal the

problem.

RECOVERY

 

FUNCTION

Specification

Desc./Quantity

air temperature

25 °C (77 °F)

engine temperature

30 °C (86 °F)

with linear increase from the air temperature at ignition

barometric pressure

1010 hPa

throttle valve potentiometer

2.9° at idle, otherwise variable.

idle motor

fixed value variable depending on the vehicle

Using axone for injection system

Injection

Stelvio 1200 NTX ABS

Power supply

P SUPP - 185

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды